One Centrifuge to fit All your needs.
The stackable, easy swap “rack-in-rotor” system and refrigerated, high-speed capability leads to tremendous time savings
STACKABLE “RACK-IN-ROTOR” SYSTEM.
This system allows you to stack up to 3 racks, allowing up to 72 1.5/2.0 mL microtubes in one cycle. Do more, save more time.
INSTANT ROTOR SWAP.
Easily and instantly swap rotors for everything from 1.5 / 2.0 mL tubes to 96-well plates to 50 mL tubes. No need to pull out tools or buy several centrifuges to accommodate your large array of tubes and sample media.
Runs at up to 16,000 RPM / 21,130G. The high-power motor and inverter gets your centrifuge running at full capacity (up to 16,000 rpm in under 20 seconds). LOTS of power.
The chamber can cool down to the set temperature down to -9°C within three minutes*.
The unique floor-standing design combined with high-capacity and flexibility eliminate the need for several centrifuges and frees your benchtop.
MANY CENTRIFUGES IN ONE.
With its ability to quickly and easily accommodate rotors for tubes of just about every size eliminates the need to have an arsenal of centrifuges occupying your lab space.
The uniquely compact floor-standing design and small footprint (345W x 465D x 860H mm) frees up valuable benchtop space for other equipment and most importantly, saves space for your work.
Allows easy movement and storage of your centrifuge. When not in use, easily move it under a bench or to a comfortable, quiet corner of your laboratory.
Easy to load, easy to see, easy to use. Easy!
The rotor / rack system not only takes away the need to load / unload each and every tube every single time, it serves as a handy “rack” making it easy to move your sample to your benchtop or the refrigerator and back to the centrifuge again
The intuitive display and rotating jog dial allows you to easily and intuitively adjust time, speed and temperature settings.
PRESET MEMORY FUNCTION.
Allows programming of 2 preset settings to easily switch back and forth between your favorite settings- quick and easy!
Set the timer from 1-99 minutes and save your time for other business.
Saves You, Safety for You and Your Samples.
Safety, not only for you, but your samples and larger things.
SAFETY AND ABNORMALITY DETECTION.
The lid interlock system electronically locks and prevents the lid from opening while in operation. Smart sensing systems for everything from lid open/close, rotor imbalance, excessive speed, motor over-current (with circuit breaker), and abnormal chamber temperature.
Gradually brings down the speed of your centrifuge to protect your samples (45 sec slow deceleration from 500RPM to 0).
ROTOR IDENTIFICATION SYSTEM.
Recognizes the rotor type to set appropriate speed limits.
Controlling the motor fan drive during standby cooling, leads to a reduction in power consumption by up to 43%*, in the grand scheme helping to save you.
*Reduction in electricity consumption between the MX-307 and previous generation MX-305. This figure may vary depending on the settings and performance of individual products.
|Maximum Speed||16,000 rpm||Maximum RCF||21,130 G|
|Maximum Capacity||50 ml x 4||Control System||Microprocessor control (Feedback System)|
|Drive Motor||Induction Motor||Drive System||Direct drive with an automatic alignment function|
|Data Entry Device||Jog Dial||Temperature Setting Range||– 9 to 35°C (1°C increment)|
|Speed Setting Range||300 rpm to Maximum speed (100 rpm increments)||RCF Setting Range||100 G to Maximum RCF (100 G increments)|
|Time Setting Range||0 to 99 minutes (1minute increment) or, for free||Additional Functions||• FLASH (momentary spin) function
• Memory function(two sets)
• Previous setting memory
• Soft Brake function
|Safety Devices||• Lid interlock
• Lid open/close detector
• Over-speed detector
• Over-current circuit breaker
• Motor over-current detector
• Abnormally high or low chamber temperature detector
• Rotor identification system
• Imbalance detector
|Accessories Included||• Operator’s manual (1)
• Warranty card (1)
• Customer card (1)
• Inspection sheet (1)
• Hexagon wrench (1)
• Clear storage case (1)
• Attaching screw (1)
• Caster holder (2)
• Drain plug (1)
|Power Requirements||Single phase AC110/120V 50/60Hz, 15ASingle phase AC220/230/240V 50/60Hz, 8A||Power Consumption
|860 W (740 kcal/h)|
|Dimensions (except protrusion)||345 W x 465 D x 860 H mm (table height: 755 H mm, lid open position: 1125 H mm )||Net Weight||66 kg (110/120V), 71 kg (220/230/240V)|
|Cord Length||3 m||Refrigerant||HFC134a (240 g)|
|Environmental Requirements||Ambient temperature range: 10 to 35°C, Relative humidity: 30 to 85%, Atmospheric pressure: 700 to 1060 hPa|
*Specifications and design are subject to change for improvement without prior notice. Please ask for the latest specifications prior to your order and procurement.
Centrifuge MX Series Brochure